![]() ![]() Cross hipped: The result of joining two or more hip roof sections together, forming a T or L shape for the simplest forms, or any number of more complex shapes.N–S and E–W) compared to the one pair of direction (e.g. Hip, hipped: A hipped roof is sloped in two pairs of directions (e.g.Hidden roof: A type of Japanese roof construction.Karahafu: A type of gable found in some traditional Japanese buildings.A kink separates the roof into two parts running towards each other at an obtuse angle. Butterfly roof (V-roof, London roof ): A V-shaped roof resembling an open book.Monitor roof: A roof with a monitor 'a raised structure running part or all of the way along the ridge of a double-pitched roof, with its own roof running parallel with the main roof.'.Bonnet roof: A reversed gambrel or Mansard roof with the lower portion at a lower pitch than the upper portion.Saltbox, catslide: A gable roof with one side longer than the other, and thus closer to the ground unless the pitch on one side is altered.Overhanging eaves forming shelter around the building are a consequence where the gable wall is in line with the other walls of the buildings i.e., unless the upper gable is recessed. ![]() the opposite arrangement to the half-hipped roof. Dutch gable, gablet: A hybrid of hipped and gable with the gable (wall) at the top and hipped lower down i.e.Half-hipped (clipped gable, jerkinhead ): A combination of a gable and a hip roof (pitched roof without changes to the walls) with the hipped part at the top and the gable section lower down.See also roof pitch, crow-stepped, corbie stepped, stepped gable: A gable roof with its end parapet walls below extended slightly upwards and shaped to resemble steps.Cross gabled: The result of joining two or more gabled roof sections together, forming a T or L shape for the simplest forms, or any number of more complex shapes.Gable (ridged, dual-pitched, peaked, saddle, pack-saddle, saddleback, span roof ): A simple roof design shaped like an inverted V.Saw-tooth: Multiple single-pitched roofs arrayed in a row, sometimes seen on factories.Shed roof (lean-to, pent roof, skirt roof, outshot, skillion, mono-roof ): A roof with one slope, historically attached to a taller wall.Although referred to as flat they are generally gently pitched. Modern materials which are highly impermeable to water make possible the low-pitch roofs found on large commercial buildings. Flat: These are found in traditional buildings in regions with a low precipitation.Roof shapes Towers, especially church towers, frequently feature special roof shapes ![]() Usages vary from region to region, nation to nation, and from one builder or architect to another. Roof shapes differ greatly from region to region, depending on the climate, materials available, customs, and many other considerations. Roof angles are an integral component of roof shape, and vary from almost flat to steeply pitched. However, slide the smooth edge of the new piece of soffit into the groove of the first piece of soffit.Roof shapes include flat (or shed), gabled, hipped, arched, domed, and a wide variety of other configurations detailed below. Step 6 - Install Next Sectionīegin installing the next piece of soffit, following the same process as before. Nail the close edge of the soffit to the facia, starting by placing a roofing nail in the center of the section. This will prevent the soffit from bending. Before nailing the soffit into place, slide a small amount of the soffit out of the back of the F-channel. Starting at the bottom edge of one gable, slide the soffit into the F-channel. This will provide space for the expansion and contraction of the soffit with cold and hot weather, and prevent warping. One side of the soffit has a groove which will be used to stabilize the jointing pieces of cut soffit.Ĭut the soffit into pieces the same width as the subfacia, subtracting 1/8 inch. These ridges will be placed perpendicular to the house when the soffit is installed. The soffit comes in a long strip but has ridges running down the length of the strip. The F-channel will hold the soffit in place and hide it from view from the exterior of the house. This channel will run the entire length of the gable, running from the bottom of the gable to the upper tip of the gable, including along the other side. Wearing protective gloves and protective eye wear, place the F-channel mold along the underside of the subfacia. Generally an overhang will be approximately 12 inches, but measure carefully since there are variations for each home. Measure the width of the subfacia (space on the underside of the eave from the wall to the outer eave board). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |